
How to clean an aircon filter in 7 steps

By Urban Company
7 min read
Nov 15, 2026
Wash an aircon filter in 7 steps: rinse it from the back in the shower, dry it in the shade, and check it once a month, as NEA advises.
You can wash an aircon filter yourself in
7 steps
: switch off, open the panel, take the filters out, clear the loose dust, rinse from the back, dry in the shade and refit. The mesh is a dust screen that keeps lint off the coil; a clean one lets air flow freely again so the unit cools properly. After that, NEA’s advice is to
check the filter once a month
(
NEA energy-saving tips).
Key takeaways
Switch off at the isolator before you open the panel.
Clear loose dust dry first, then rinse from the back in the shower area.
Dry the filters fully in the shade before you refit them.
NEA advises checking the filter once a month.
Dirt on the coil, blower or drain tray needs a professional clean.
How to clean an aircon filter, step by step
These steps are for the wall-mounted split unit that most flats and condos have; for cassette and ceiling units, follow the manual. You need a stable step stool, a towel, a soft brush (an old toothbrush works) and a little mild dishwashing liquid. In many HDB bedrooms the unit sits right above the bed, so stand on the stool, not the mattress.
Switch off with the remote, wait for the louvre blades to close on their own, then switch off at the isolator (the switch on the wall near the unit).
Open the front panel. Hold both lower corners and lift until it stays up. On some models the panel unhooks completely, and the manual will say so. Don’t force it past where it stops.
Take out the filters. There are usually 2. Push the tab up slightly, then pull each one down and out. Note which way round it sits. If a thin extra filter is clipped onto the mesh, unclip it and check the manual before wetting it, because many of these can’t be washed.
Clear the loose dust dry, before any water. Vacuum the dusty side with a brush head, or tap the filter gently into a bin bag. Wet dust turns to paste that’s harder to shift. If you live in an HDB block, do this indoors, not over the common corridor or out of the window.
Rinse from the back, in the shower area. Hold the filter over the shower floor and run lukewarm water from the handheld shower through the clean side of the mesh, so it pushes dust out the way it came in. The floor drain takes the grey water, so skip the kitchen or basin sink. Add a drop of dishwashing liquid for greasy film, which is common on units near an open kitchen, and brush gently along the mesh. No hot water, no bleach, no stiff scrubbing brush.
Dry it fully, in the shade. Shake off the water and stand the filters upright on a towel. In Singapore’s humidity this can take a few hours. A filter refitted damp is an easy way to start a musty smell.
Refit and wipe down. Slide each filter back the same way round until it seats, close the panel until it clicks, and wipe the panel and the outside of the louvres with a damp cloth. Don’t push the louvre blades by hand, because they’re motor-driven. Then switch back on at the isolator.
What to look at while the panel is open
With the filters out, shine a torch into the unit. You’re looking, not touching. The thin metal fins you see are the front of the evaporator coil, and just below it, through the louvre opening, is the blower wheel, a long drum-shaped fan.
What the torch shows
What it usually means
Bright fins, light dust
Fine: filter is working
Grey felt on the fins
Coil needs a clean
Black specks on blower
Grime on the fan
Water in unit or musty
Drain may be choked
Don’t brush, vacuum or spray the fins. They bend like foil, and once folded over they block airflow for good. Store-bought coil sprays don’t solve it either. The dirt they loosen has to be rinsed out of the unit, and without that rinse it ends up in the drain tray.
How often to clean an aircon filter
Go back to NEA’s rule of thumb:
check it once a month
, and clean it when it looks grey or you can’t see light through the mesh. Check sooner if there’s renovation going on in your block, if the unit runs all day, or if you have a pet that sheds.
BCA also asks owners to inspect the outdoor unit’s supports for corrosion or damage
at least every 6 months
(
BCA, air-conditioning safety). Look from inside the window, and never lean or climb out to check.
Why a clean filter doesn’t fix everything
A filter wash clears the screen at the front. The parts that cause most lasting problems sit behind it:
The evaporator coil collects whatever slips past the filter. A coated coil cools less, and a heavily clogged one can even frost over. A dirty filter is a common cause of that.
The blower wheel is where black specks and a stale smell build up. Reaching it means taking the casing off around live electrics.
The drain tray catches the water the coil pulls out of the air. When slime builds up there, you get smells first and drips down the wall later.
None of these can come out by hand, and cleaning them means containing a lot of dirty water above your bed or sofa. That’s the point where a filter wash has done all it can. If ice is already forming on the coil,
why an aircon freezesexplains what to do next.
How a Professional cleans what’s behind the filter
This is what FoamJet servicing is for, and it’s how Urban Company cleans the parts behind the filter. The Professional applies foam to the front and back of the evaporator coil, the filters, the drain tray and the blower wheel, lets it lift the grime, then jet-washes it all out. You see the dirty water at the end.
How FoamJet servicing workscovers each step.
When you book, FoamJet Servicing for 2 units is $46 and takes about an hour, and from 3 units it's $20 a unit. Urban Company's Aircon Servicing is rated 4.88 from 138K bookings. Book it if the filter is clean and the torch check above showed a grey coil or a dirty blower, if a smell comes back within days of a wash, or if airflow is still weak. Otherwise, a monthly filter wash is enough. If the room still isn't cold after all that,
why your aircon is not coolingcovers the other causes.
Frequently asked questions
How do I know my aircon filter is dirty?
Lift the front panel and look. A clean mesh lets you see light through it; a dirty one looks grey or furry. Other signs are weaker airflow from the vents and a room that takes longer to cool. If the mesh looks clean but those signs stay, the dirt is probably on the coil or blower behind it.
Can I run the aircon while the filter is drying?
Better not. With the filters out, room dust goes straight onto the evaporator coil, which is the one part you can’t rinse yourself. Wash the filters in the morning so they have the day to dry, or use a fan in that room for the evening. Slot them back only when they are completely dry.
Can I put the aircon filter in the washing machine or dishwasher?
No. The heat and tumbling in a washing machine or dishwasher can warp the plastic frame and tear the fine mesh, and a filter that no longer sits flat lets dust slip past onto the coil. Hand-rinse it from the back under lukewarm water instead, as in step 5, and let it dry in the shade.
Can I dry the aircon filter with a hair dryer or in the sun?
Neither is a good idea. Hot air and strong afternoon sun can warp the plastic frame, and a warped filter won’t sit flat, so dust slips past it onto the coil. Shake off the water, stand the filters upright on a towel in the shade, and give them a few hours.
Should I replace my aircon filter instead of washing it?
Only if it is damaged. A standard mesh filter is made to be washed again and again. Replace it if the mesh is torn, the frame is cracked or bent, or the clips no longer hold. Use a filter made for your model, which your unit’s manual or the maker’s spare-parts list will name.
When the filter is clean but the coil, blower or drain tray isn’t, a Professional can take it from there.
Book FoamJet aircon servicing in Singaporewith Urban Company, with the price for your number of units shown before you book.













