
Aircon not turning on? 6 causes and what to check first

By Urban Company
7 min read
Nov 15, 2026
Aircon not turning on? It's usually 1 of 6 causes. See what's safe to check yourself, when to stop, and what a $60 diagnosis covers.
It's 11pm in your 3-room flat in Tampines and the bedroom is still 30°C. You press the remote and nothing happens. No beep, no flap opening, just a small light on the indoor unit blinking at you. Before you assume the worst, work through the checks below.
Key takeaways
An aircon not turning on usually comes down to 1 of 6 causes, and 4 of them you can check yourself. If it's none of those, an Urban Company power-issue diagnosis costs $60 in Singapore and takes about 60 minutes. The $60 visit fee is replaced with the valid service cost if you go ahead with the repair.
Check in this order: the remote, the isolator switch, the breaker in your DB box, then any timer setting. Most no-starts end at one of these.
A blinking light on the indoor unit is usually an error code, not a timer. The unit has stopped itself because it found a fault.
Reset a tripped breaker once only. If it trips again, leave it off and get the unit checked.
Stop straight away if you smell burning, see scorch marks or the isolator feels hot. Never open the unit, the switch or the DB box cover.
Why is my aircon not turning on?
Because the unit isn't getting a signal, isn't getting power, or has stopped itself to protect against a fault.
The 6 usual causes:
The remote. Flat batteries, a lock setting, or a remote that has stopped sending a signal.
The isolator switch or power point is off. Someone switched it off during a clean, a renovation or a long trip away.
A tripped breaker. The aircon's switch in the DB box has tripped, or the main RCCB has cut the whole flat.
A timer setting. An on-timer or off-timer is still set from last time.
An error code. The unit has detected a fault (a sensor, the fan, the outdoor unit or the control board) and won't run until it's fixed.
A full drain tray. On units with a float switch, backed-up water cuts the power to stop an overflow.
What does each sign mean?
What the unit does when you press the remote narrows it down quickly.
Sign
Likely cause
What to do
Remote screen blank
Flat batteries
Change batteries
No lights on unit
Isolator off or tripped
Check isolator, breaker
Breaker trips on start
Unit or wiring fault
Call a Professional
Works by button only
Remote or receiver
New batteries first
Timer light on
Timer still set
Cancel the timer
Light blinks in pattern
Error code
Restart once, then call
Dripped, then stopped
Float switch cut-off
Get the drain cleared
Burning smell or heat
Electrical fault
Switch off, call now
What should you check first?
Start with what costs nothing and needs no tools.
The remote. If the screen is blank or faint, change both batteries. Point it straight at the indoor unit and press once. Many wall units also have a small manual button under the front panel. If the unit starts from that button but not from the remote, the remote is the likely problem.
The isolator switch. Split aircons in HDB flats and condos are usually wired to an isolator switch on the wall, often near the indoor unit and sometimes near the outdoor unit. Make sure it's on. Use dry hands and only the switch itself.
The DB box. Look at the row of switches in your distribution board. If the aircon's switch, or the RCCB for the whole flat, is down, turn the aircon off at the isolator and push the switch back up once. Never unscrew the cover or touch anything behind the switches.
The timer. Look for a timer symbol on the remote screen or a timer light on the unit, and cancel it. An on-timer or off-timer set weeks ago is easy to forget.
After a power cut, wait a few minutes. Many units hold off restarting the compressor for a short while to protect it.
What does a blinking light on your aircon mean?
On most units, a light blinking in a repeating pattern is a self-diagnosis code.
The unit has found a fault and shut itself down. On some models it's the timer light that blinks, which is why people often search for "aircon timer light blinking" when nothing about the timer is wrong.
The pattern means different things on different brands, so count the blinks and check your manual or the label inside the front panel. Then turn the unit off at the isolator, wait a few minutes, and switch it back on once. If the same pattern returns, write it down and leave the unit off. It's a fault that needs a Professional, and telling them the pattern saves time on the visit.
Can a full drain tray stop your aircon turning on?
Yes, on units with a float switch.
Cassette and ceiling units usually have one, and some wall units fitted with a drain pump do too. When the drain chokes and water backs up into the tray, the float rises and cuts the unit off before it can overflow onto your ceiling or floor.
Signs: the unit stops or won't start, there may be a blinking light, and you may have noticed dripping before it died. Clearing the drain is a job for a Professional. Our guide to
why an aircon drips waterexplains the usual causes of a choked drain. Regular servicing helps keep that drainage path clear.
If several rooms run off 1 outdoor unit and
none
of them will start, the problem is more likely the shared outdoor unit or its supply. See
types of aircon in Singapore homes.
When should you stop and call a Professional?
Stop as soon as there's any sign of an electrical fault, or once the simple checks are done and the unit still won't run.
Call a Professional if:
The breaker trips again when the aircon starts.
The isolator or power point feels hot, buzzes, crackles or has scorch marks.
You smell burning from the unit or the switch.
The same error code comes back after one restart.
The indoor unit runs but the outdoor unit stays silent.
If the indoor unit runs but nothing comes out cold, that's a different problem. See
why an aircon stops cooling.
If you can do so safely, switch off at the isolator or the breaker and leave everything closed. Don't open the casing, the isolator or the DB box, and don't try to test wiring. In an HDB flat the outdoor unit sits on a ledge or bracket outside the window, so don't climb out to look at it. BCA advises owners to
have a trained installer check the outdoor unit's supports during servicing.
How much does it cost to fix an aircon that won't turn on?
It depends on the cause, so the first step is a diagnosis.
With Urban Company, a power-issue diagnosis is
$60 and takes about 60 minutes
. The $60 visit fee is replaced with the valid service cost if you go ahead with the repair, so it isn't charged on top of the fix.
A failed remote costs you a pair of batteries. A tripped breaker caused by a one-off surge costs nothing. A faulty control board, sensor or fan motor is a repair, and the diagnosis visit finds which part it is. For what regular servicing costs, read our guide to
aircon servicing costs in Singapore, or
see aircon repair prices and book.
Frequently asked questions
Why is my aircon not turning on with the remote?
Start with the remote itself. If its screen is blank or faint, change both batteries. Point it straight at the indoor unit from a few metres away, and check it isn't on a lock or a different mode. If the unit starts from its manual button but not the remote, the remote or the unit's receiver is the problem.
Why is my aircon timer light blinking?
On many units, a blinking timer or operation light is a self-diagnosis code rather than a timer setting. The unit has found a fault and stopped itself. Count the blinks and check your manual. Switch off at the isolator for a few minutes and try once more. If it blinks again, get it checked.
What should I do if my aircon trips the breaker?
Switch the aircon off, then push the tripped switch in your DB box back up once. If it trips again when the aircon starts, leave it off and don't keep resetting it. A repeat trip points to a fault in the unit or its wiring, and that needs a trained Professional.
Can a full drain tray stop an aircon from turning on?
Yes, on units fitted with a float switch. Cassette and ceiling units usually have one, and some wall units do too. When water backs up in the tray, the switch cuts the unit off to stop an overflow. Clearing the choked drain is a job for a Professional, and the unit should restart once it's done.
Why won't my aircon turn on after a power cut?
Give it a few minutes. Many units wait before restarting the compressor after power returns, to protect it. Check the isolator and the DB box too, because a power cut can trip a breaker. If the unit still shows no lights at all once power is back everywhere else, a Professional should check it.
How much does it cost to fix an aircon that won't turn on?
It depends on the cause, so the first step is a diagnosis. With Urban Company, a power-issue diagnosis is $60 and takes about 60 minutes. The $60 visit fee is replaced with the valid service cost if you go ahead with the repair, so it isn't charged on top of the fix.













